Differences

This shows you the differences between two versions of the page.

--- resources:eval:user-guides:circuits-from-the-lab:cn0254 [26 Sep 2017 08:04] – update Trisha Cabildo
+++ resources:eval:user-guides:circuits-from-the-lab:cn0254 [30 Jul 2021 07:26] (current) – Victor Calinao, Jr
@@ Line 15: / Line 15: @@
 ===== Required Equipment =====
   * [[adi>EVAL-CN0254-SDPZ|EVAL-CN0254-SDPZ Evaluation Board]]
-  * [[http://www.analog.com/EVAL-SDP-CB1Z|EVAL-SDP-CB1Z]] Controller Board (**SDP-B Board**)
+  * [[adi>EVAL-SDP-CB1Z|EVAL-SDP-CB1Z]] Controller Board (**SDP-B Board**)
   * [[ftp://ftp.analog.com/pub/cftl/CN0254/|CN0254 Evaluation Software]]
   * DC Power Supply (6 V, 500 mA)
@@ Line 26: / Line 26: @@
 ==== Block assignments ====
 {{ :resources:eval:user-guides:circuits-from-the-lab:cn0254:blockdia.png?nolink&650 |}}\\
-  * The [[http://www.analog.com/EVAL-CN0254-SDPZ|EVAL-CN0254-SDPZ]] **(CN-0254 Board)** connects to the [[http://www.analog.com/EVAL-SDP-CB1Z|EVAL-SDP-CB1Z]] **(SDP-B Board)** via the 120-Pin connector
+  * The [[adi>EVAL-CN0254-SDPZ|EVAL-CN0254-SDPZ]] **(CN-0254 Board)** connects to the [[adi>EVAL-SDP-CB1Z|EVAL-SDP-CB1Z]] **(SDP-B Board)** via the 120-Pin connector
-  * The [[http://www.analog.com/EVAL-SDP-CB1Z|EVAL-SDP-CB1Z]] **(SDP-B Board)** connects to the PC via the USB cable.
+  * The [[adi>EVAL-SDP-CB1Z|EVAL-SDP-CB1Z]] **(SDP-B Board)** connects to the PC via the USB cable.
   * Terminal block **CN2** is the +6 V power supply input
+  * Terminal block **J2** is for the multiple channels analog input
+  * Jumper **J3** is the test point for SPI data lines
+\\
+==== Test setup ====
+{{ :resources:eval:user-guides:circuits-from-the-lab:cn0254:11-2-2017_10-50-05_am.png?nolink&600 |}}\\
+  - Connect the 120-pin connector on the [[adi>EVAL-CN0254-SDPZ|EVAL-CN0254-SDPZ Evaluation Board]] to the connector marked “CON A” on the [[adi>EVAL-SDP-CB1Z|EVAL-SDP-CB1Z]] evaluation (SDP) board
+  - After setting the dc output supply to 6 V output, turn the supply off
+  - With power to the supply off, connect 6 V to CN2
+  - Turn on the power supply and then connect the SDP to the PC by using the USB-to-miniUSB cable
 \\
@@ Line 36: / Line 44: @@
 </WRAP>
+\\
+----
+===== Installing the Evaluation Software =====
+  - Extract the file **CN0254_Evaluation_Software.zip** and open the file **setup.exe**.\\ \\ <WRAP left tip round box 60%>**NOTE:** It is recommended that you install the [[ftp://ftp.analog.com/pub/cftl/CN0254/|CN0254 Evaluation Software]] to the default directory path **C:\Program Files (x86)\Analog Devices\CN0254\** and all National Instruments products to **C:\Program Files\National Instruments\**</WRAP> {{:resources:eval:user-guides:circuits-from-the-lab:cn0254:1.png?nolink&500|}}
+  - Click **Next** to view the installation review page\\ \\ {{:resources:eval:user-guides:circuits-from-the-lab:cn0254:2.png?nolink&500|}}\\ \\
+  - Click **Next** to start the installation\\ \\ {{:resources:eval:user-guides:circuits-from-the-lab:cn0254:3.png?nolink&500|}}\\ \\
+  - Upon completion of the installation of the **CN-0254 Evaluation Software**, the installer for the **ADI SDP Drivers** will execute.\\ \\ <WRAP left tip round box 60%>**NOTE:** It is recommended that you close all other applications before clicking **“Next”**.  This will make it possible to update relevant system files without having to reboot your computer.</WRAP>\\ \\ {{:resources:eval:user-guides:circuits-from-the-lab:cn0254:4.png?nolink&500|}}\\ \\
+  - Press **“Next”** to set the installation location for the **SDP Drivers**.\\ \\ <WRAP left round tip 50%>It is recommended that you install the drivers to the default directory path \\ **C:\Program Files\Analog Devices\SDP\Drivers**</WRAP>\\ \\ {{:resources:eval:user-guides:circuits-from-the-lab:cn0254:5.png?nolink&500|}}\\ \\
+  - Press **“Next”** to install the **SDP Drivers** and complete the installation of all software.  Click **"Finish"** when done.\\ \\ {{:resources:eval:user-guides:circuits-from-the-lab:cn0254:6.png?nolink&500|}}
+----
+===== Using the Evaluation Software =====
+==== Main Window ====
+{{ :resources:eval:user-guides:circuits-from-the-lab:cn0254:13.png?nolink&700 |}}
+  - **Connect** Button - Starts the connection between the [[ADI>CN0254|CN0254 Evaluation Board]] and [[ADI>EVAL-SDP-CB1Z|SDP-B Controller Board]].
+  - **Disconnect** Button - ends the connection between the [[ADI>CN0254|CN0254 Evaluation Board]] and [[ADI>EVAL-SDP-CB1Z|SDP-B Controller Board]]
+  - **Start** Button - Start acquisition of measurement data
+  - **Save Data** - Save the data collected to a tab delimited ASCII spreadsheet file
+  - **General control** Section \\
+      * **Connector** - Selects which 120-pin connection of the SDP-B Board to use
+      * **Input Signal Range** - Select range of analog signal input
+      * **Sample Rate/CH** - Set desired sample rate per channel
+      * **Samples/CH** - Set number of samples to be taken per channel
+      * **Scan mode** - Select between single or multiple channel data acquisition
+      * **Channel Setting for Scan mode** - Select which channel/s to be used for data acquisition
+      * **Capture Mode** - Choose between single or continuous capturing of data
+      * **Bandwidth** - Select bandwidth for low-pass filter in ADC that reduces undesirable aliasing effects and limits the noise from the driving circuitry
+      * **Phase Compensation** Checkbox - Compensate unbalanced differential input voltages to the comparator
+      * **Calibration** Checkbox - Turn ON/OFF Calibratration
+  - **Multi-Channel** Tab \\ {{ :resources:eval:user-guides:circuits-from-the-lab:cn0254:9.png?nolink&700 |}}
+      * **Plot options per channel** - Edit plot display and options like interpolation and color of output waveform
+      * **Display Format** - Select y-axis of plotted graph between RAW data or voltage
+      * **Graph Controls** - Allow the user to zoon in, zoom out, and pan through the data collected
+      * **Scale Fit Setting** - Allows user to or not to autoscale the output on the graph
+  - **Single Channel** Tab \\ {{ :resources:eval:user-guides:circuits-from-the-lab:cn0254:10.png?nolink&700 |}}
+      * **Time Domain** Tab - Shows the acquired measurement data in terms of ADC codes with respect to time
+      * **Frequency Domain** Tab - Plots the FFT of the the ADC samples with the amplitudse in dB of the full scale ADC value
+      * **Histogram** Tab - Plots the number of occurrences of ADC sample values
+      * **Signal Parameters** - Read only. Shows parameters such as SFDR of the signal chosen through the radio buttons on the right side of user interface
+  - **Calibration** Tab - Contains the calibration instructions for the CN0254 Evaluation Board\\ {{ :resources:eval:user-guides:circuits-from-the-lab:cn0254:11.png?nolink&700 |}}
+      * **Precision Voltages** - Set the low and high precision voltages to be used for calibration
+      * **Input Range** - Select range of analog signal input
+      * **Overwrite EEPROM** Checkbox - If selected, precision voltage parameter will be saved into EEPROM after calibration is complete
+      * **Calibrate** - Start calibration of the device
+      * **Recover to Default Value** - Recover the original default values of precision voltages of the device from the EEPROM
+      * **Write Factory Default** - Writes precision voltages from calibration to an array in EEPROM and sets them as the factory default values
+  - **S/W Version Info** Tab \\ {{ :resources:eval:user-guides:circuits-from-the-lab:cn0254:12.png?nolink&700 |}}
+      * **Flash LED** - Flashes the LED on the SDP controller board
+      * **Read Firmware** - Reads the firmware of CN0254 Evaluation Board
+\\
+==== Running the System ====
+  -Open the CN0254.exe application from the default installation location
+  -Set the correct connector and click the Connect Button
+  -Upon successful connection, calibrate the device in the Calibration tab by following the instructions indicated
+  -After proper calibration, select the desired settings like signal ranges and such
+  -Press the Start button
+  -If you want to save the data to file, press the Save Data button
+  -Click Quit to exit the software
+\\
+----
+===== More Information and Useful Links  =====
+  * [[ftp://ftp.analog.com/pub/cftl/CN0254/|CN0254 Evaluation Software]]
+  * [[ADI>CN0254|CN0254 Circuit Note Page]]
+  * [[ADI>CN0254 -DesignSupport|CN0254 Design Support Package]]
+  * [[ADI>AD8605|AD8605 Product Page]]
+  * [[ADI>AD8609|AD8609 Product Page]]
+  * [[ADI>AD7689|AD7689 Product Page]]
+  * [[ADI>ADUM3471|ADUM3471 Product Page]]
+  * [[ADI>ADP3336|ADP3336 Product Page]]
+  * [[ADI>AD8608|AD8608 Product Page]]
+  *
+===== Schematic, PCB Layout, Bill of Materials =====
+<WRAP round 80% download>
+[[adi>media/en/reference-design-documentation/design-integration-files/CN0254-DesignSupport.zip|EVAL-CN0254-SDPZ Design & Integration Files]]
+  * Schematics
+  * PCB Layout
+  * Bill of Materials
+  * PADS project
+</WRAP>
+=====Registration=====
+<WRAP round tip 80% >
+Receive software update notifications, documentation updates, view the latest videos, and more when you register your hardware.  [[reg>EVAL-CN0254-SDPZ?&v=Rev A|Register]] to receive all these great benefits and more!</WRAP>
+// End of Document //

Wiki

Analog Devices Wiki

Differences

Analog Devices Wiki

Differences

Page Tools