Wiki

Analog Devices Wiki

English
English
简体中文
简体中文
日本語
日本語
Руccкий
Руccкий

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Next revision		Previous revision
resources:eval:user-guides:circuits-from-the-lab:cn0229 [07 Aug 2017 05:55] – created Trisha Cabildoresources:eval:user-guides:circuits-from-the-lab:cn0229 [30 Jul 2021 07:23] (current) – Victor Calinao, Jr
Line 3: Line 3:
 [[ADI>CN0229]] is a multichannel, flexible, analog output solution with only two analog components and meets most requirements for multichannel I/O cards, programmable logic controllers (PLCs), and distributed control systems (DCSs) applications. The circuit also contains key features for industrial applications, such as on-chip output fault detection, packet error checking (PEC) by the CRC, flexible power-up options, and ESD protection making it an ideal choice for robust industrial control systems. [[ADI>CN0229]] is a multichannel, flexible, analog output solution with only two analog components and meets most requirements for multichannel I/O cards, programmable logic controllers (PLCs), and distributed control systems (DCSs) applications. The circuit also contains key features for industrial applications, such as on-chip output fault detection, packet error checking (PEC) by the CRC, flexible power-up options, and ESD protection making it an ideal choice for robust industrial control systems.
  
-The [[ADI>AD5750/AD5750-1/AD5750-2]] are all single-channel, low cost, precision voltage/current output drivers developed to meet the requirements of industrial process control applications. The voltage output range can be programmed for the standard output ranges for PLC and DCS applications: 0 V to 5 V, 0 V to 10 V, −5 V to +5 V, and −10 V to +10 V with a 20% overrange setting provided for the standard ranges. The current output, which is provided on a separate pin, can be programmed for the ranges of 4 mA to 20 mA, 0 mA to 20 mA, −20 mA to +20 mA, 0 mA to 24 mA, and −24 mA to +24 mA. The unipolar ranges have a 2% overrange setting.+The [[ADI>AD5750-2]] is a single-channel, low cost, precision voltage/current output driver developed to meet the requirements of industrial process control applications. The voltage output range can be programmed for the standard output ranges for PLC and DCS applications: 0 V to 5 V, 0 V to 10 V, −5 V to +5 V, and −10 V to +10 V with a 20% overrange setting provided for the standard ranges. The current output, which is provided on a separate pin, can be programmed for the ranges of 4 mA to 20 mA, 0 mA to 20 mA, −20 mA to +20 mA, 0 mA to 24 mA, and −24 mA to +24 mA. The unipolar ranges have a 2% overrange setting.
  
 The [[ADI>AD5686R]] is a quad 16-bit nanoDAC+ with rail-to-rail voltage-buffered outputs integrated with an on-chip 2 ppm/°C typical (5 ppm/°C maximum), 2.5 V reference. The on-chip reference can drive the reference input of all four AD5750-2s, has a low output impedance of 0.05 Ω, and can source and sink up to 5 mA.  The [[ADI>AD5686R]] is a quad 16-bit nanoDAC+ with rail-to-rail voltage-buffered outputs integrated with an on-chip 2 ppm/°C typical (5 ppm/°C maximum), 2.5 V reference. The on-chip reference can drive the reference input of all four AD5750-2s, has a low output impedance of 0.05 Ω, and can source and sink up to 5 mA. 
Line 15: Line 15:
 ===== Required Equipment ===== ===== Required Equipment =====
   * [[adi>EVAL-CN0229-SDPZ|EVAL-CN0229-SDPZ Evaluation Board]]   * [[adi>EVAL-CN0229-SDPZ|EVAL-CN0229-SDPZ Evaluation Board]]
-  * [[http://www.analog.com/EVAL-SDP-CB1Z|EVAL-SDP-CB1Z]] Controller Board (**SDP-B Board**)+  * [[adi>EVAL-SDP-CB1Z|EVAL-SDP-CB1Z]] Controller Board (**SDP-B Board**)
   * [[ftp://ftp.analog.com/pub/cftl/CN0229/|CN0229 Evaluation Software]]   * [[ftp://ftp.analog.com/pub/cftl/CN0229/|CN0229 Evaluation Software]]
   * Triple Output DC Power Supply (6 V, +15 V and -15 V)   * Triple Output DC Power Supply (6 V, +15 V and -15 V)
Line 22: Line 22:
       * //Agilent 34401A 6.5 Digital Multimeter//       * //Agilent 34401A 6.5 Digital Multimeter//
   * PC with the following //Minimum Requirements//   * PC with the following //Minimum Requirements//
-      * Windows 2000 or Windows XP+      * Windows 7 or higher
       * USB interface       * USB interface
-  * USB type A to USB type mini-B cable 
  
 ---- ----
 ===== General Setup ===== ===== General Setup =====
 ==== Block assignments ==== ==== Block assignments ====
-{{ :resources:eval:user-guides:circuits-from-the-lab:cn0202:bbbb.png?nolink&600 |}}\\ +{{ :resources:eval:user-guides:circuits-from-the-lab:cn0229:8-7-2017_2-02-51_pm.png?nolink&650 |}}\\ 
-  * The [[http://www.analog.com/EVAL-CN0229-SDPZ|EVAL-CN0229-SDPZ]] **(CN-0229 Board)** connects to the [[http://www.analog.com/EVAL-SDP-CB1Z|EVAL-SDP-CB1Z]] **(SDP-B Board)** via the 120-Pin connector +  * The [[adi>EVAL-CN0229-SDPZ|EVAL-CN0229-SDPZ]] **(CN-0229 Board)** connects to the [[adi>EVAL-SDP-CB1Z|EVAL-SDP-CB1Z]] **(SDP-B Board)** via the 120-Pin connector 
-  * The [[http://www.analog.com/EVAL-SDP-CB1Z|EVAL-SDP-CB1Z]] **(SDP-B Board)** connects to the PC via the USB cable. +  * The [[adi>EVAL-SDP-CB1Z|EVAL-SDP-CB1Z]] **(SDP-B Board)** connects to the PC via the USB cable. 
-  * Terminal block CN1 is the +/- 15 V power supply input +  * Terminal block **CN1** is the +/- 15 V power supply input 
-  * Terminal block CN2 is the +6 V power supply input +  * Terminal block **CN2** is the +6 V power supply input 
-  * 4 channels for output measurement+  * Four OUT_[x] voltage/current output channels 
 +      * **Optionally**, the [[ADI>AD5750-2]] output voltage feedback can be configured by connecting **VSENSE+** and **VSENSE-** across a selected branch in the load circuit. **VSENSE-** should be within +/- 3.0 V of the GND
  
 \\ \\
  
 <WRAP center round important 60%> <WRAP center round important 60%>
- Do not connect the USB cable to the Mini-USB connector on the SDP board before turning on the dc power supply for the EVAL-CN0229-SDPZ.+ Do **not** connect the USB cable to the Mini-USB connector on the SDP board before turning on the dc power supply for the **EVAL-CN0229-SDPZ**.
 </WRAP> </WRAP>
  
 ==== Jumper settings ==== ==== Jumper settings ====
 See image below for jumper settings. The bolded values are the default settings for the EVAL-CN0229-SPDZ. See image below for jumper settings. The bolded values are the default settings for the EVAL-CN0229-SPDZ.
-{{ :resources:eval:user-guides:circuits-from-the-lab:cn0229:cn0229_table2.jpg?nolink&800 |}}+ 
 +{{ :resources:eval:user-guides:circuits-from-the-lab:cn0229:9-11-2017_3-22-48_pm.png?nolink&600 |}}
 ---- ----
 ===== Installing the Evaluation Software ===== ===== Installing the Evaluation Software =====
Line 55: Line 56:
  
 ---- ----
 +===== Using the Evaluation Software =====
 +====Main Tab====
 +{{ :resources:eval:user-guides:circuits-from-the-lab:cn0229:8-7-2017_3-02-03_pm.png?nolink&600 |}}\\
 +  * **Connection** <fc #0000ff>(Highlighted Dark Blue)</fc>
 +      * **Connect Button**
 +          * Starts the connection with the [[ADI>CN0229|CN0229 Evaluation Board]]
 +      * **Disconnect Button**
 +          * Ends the connection with the [[ADI>CN0229|CN0229 Evaluation Board]]
 +
 +  * **System Configuration** <fc #ff0000>(Highlighted Red)</fc>
 +      * **Connector**
 +          * Selects which 120-pin connection of the SDP-B Board to use
 +      * **SLCK**
 +          * Sets the SPI clock frequency used by the evaluation board
 +
 +  * **Set/Reset** <fc #00ffff>(Highlighted Light Blue </fc><fc #ff3399> and Pink)</fc>
 +      * **Reset**
 +          * Resets AD5686R
 +      * **Set All**
 +          * Sets all channels to their corresponding settings
 +      * **Quit**
 +          * Exit the application
 +
 +
 +  * **Channel 1 Settings** <fc #ff00ff>(Highlighted Violet)</fc>
 +      * **Output**
 +          * Enables or disables Channel 1
 +      * **Range**
 +          * Sets the voltage/current output range of Channel 1
 +      * **Value**
 +          * Sets the hex value corresponding to the desired output level in Channel 1
 +
 +  * **Channel 2 Settings** <fc #008000>(Highlighted Green)</fc>
 +      * **Output**
 +          * Enables or disables Channel 2
 +      * **Range**
 +          * Sets the voltage/current output range of Channel 2
 +      * **Value**
 +          * Sets the hex value corresponding to the desired output level in Channel 2
 +
 +  * **Channel 3 Settings** <fc #B24801>(Highlighted Orange)</fc>
 +      * **Output**
 +          * Enables or disables Channel 3
 +      * **Range**
 +          * Sets the voltage/current output range of Channel 3
 +      * **Value**
 +          * Sets the hex value corresponding to the desired output level in Channel 3
 +
 +  * **Channel 4 Settings** <fc #ffff00>(Highlighted Yellow)</fc>
 +      * **Output**
 +          * Enables or disables Channel 4
 +      * **Range**
 +          * Sets the voltage/current output range of Channel 4
 +      * **Value**
 +          * Sets the hex value corresponding to the desired output level in Channel 4
 +
 +\\
 +==== Running the System ====
 +  - Open the **CN0229.exe** application from the default installation location.
 +  - Set the correct connector and SCLK settings for the board in the System Configuration section.
 +  - Click the **Connect Button** 
 +  - Upon successful connection, select the desired channel to be used.
 +  - Set the output of the channel to enable.
 +  - Select the range of desired output.
 +  - Input a corresponding hex value of the output level and select **Set CH[x]**.
 +  - In case all channels are to be used, set all desired settings for each channel and click the **Set ALL button**.
 +  - Click **Disconnect Button** if finished.
 +
 +
 +----
 +
 +===== More Information and Useful Links  =====
 +  * [[ftp://ftp.analog.com/pub/cftl/CN0229/|CN0229 Evaluation Software]]
 +  * [[ADI>CN0229|CN0229 Circuit Note Page]]
 +  * [[ADI>CN0229 -DesignSupport|CN0229 Design Support Package]]
 +  * [[ADI>AD5750-2|AD5750-2 Product Page]]
 +  * [[ADI>AD5686R|AD5686R Product Page]]
 +  * [[ADI>ADuM1301|ADuM1301 Product Page]]
 +  * [[ADI>ADuM5400|ADuM5400 Product Page]]
 +
 +===== Schematic, PCB Layout, Bill of Materials =====
 +
 +<WRAP round 80% download>
 +[[adi>media/en/reference-design-documentation/design-integration-files/CN0229-DesignSupport.zip|EVAL-CN0229-SDPZ Design & Integration Files]]
 +  * Schematics 
 +  * PCB Layout 
 +  * Bill of Materials 
 +  * PADS project
 +</WRAP>
 +
 +=====Registration===== 
 +<WRAP round tip 80% >
 +Receive software update notifications, documentation updates, view the latest videos, and more when you register your hardware.  [[reg>EVAL-CN0229-SDPZ?&v=Rev A|Register]] to receive all these great benefits and more!</WRAP>
 +
 +//End of Document//
 +
resources/eval/user-guides/circuits-from-the-lab/cn0229.1502078105.txt.gz · Last modified: 07 Aug 2017 05:55 by Trisha Cabildo

Page Tools