Differences
This shows you the differences between two versions of the page.
| Next revision | Previous revision | ||
| resources:eval:user-guides:circuits-from-the-lab:cn0204 [04 Aug 2017 04:59] – created Angelo Nikko Catapang | resources:eval:user-guides:circuits-from-the-lab:cn0204 [30 Jul 2021 07:20] (current) – Victor Calinao, Jr | ||
|---|---|---|---|
| Line 21: | Line 21: | ||
| * ±25 V/1 A Triple Output DC Power Supply (**Agilent E3631A**) | * ±25 V/1 A Triple Output DC Power Supply (**Agilent E3631A**) | ||
| * Optional Digital Multimeter for Verification (**Agilent 34401A 6.5 Digital Multimeter**) | * Optional Digital Multimeter for Verification (**Agilent 34401A 6.5 Digital Multimeter**) | ||
| - | * PC (Windows 2000 or Windows XP) with USB interface | + | * PC with USB interface |
| + | * Windows 7 or higher | ||
| ---- | ---- | ||
| Line 27: | Line 28: | ||
| ===== General Setup ===== | ===== General Setup ===== | ||
| ==== Block Assignments ==== | ==== Block Assignments ==== | ||
| + | {{ : | ||
| + | * The [[ADI> | ||
| + | * The [[ADI> | ||
| + | * Terminal block **CN1** is the current output | ||
| + | * Terminal block **CN2** is the +6 V power supply input | ||
| + | * Terminal block **CN3** is the +/- 50 V power supply input | ||
| + | * Connect the **+25 V** power supply to the **12-50 VIN** terminal | ||
| + | * Connect the **-25 V** power supply to the **GND_ISO** terminal | ||
| + | * Terminal block **CN4** is the voltage output | ||
| + | * **Optionally** if **JP3** is open, the output voltage feedback can be configured by connecting **VSENSE+** to a selected node in the load circuit | ||
| + | <WRAP center round important 60%> | ||
| + | ==== Jumper Settings ==== | ||
| + | See the table in the image below for the jumper settings. Values in red are the default settings for the [[ADI> | ||
| + | |||
| + | {{ : | ||
| + | |||
| + | ---- | ||
| + | |||
| + | ===== Installing the Evaluation Software ===== | ||
| + | - Extract the file **[[ftp:// | ||
| + | - Press **Next** to view the installation review page\\ {{: | ||
| + | - Press **Next** to start the installation\\ {{: | ||
| + | - Upon completion of the installation of the **CN0204 Evaluation Software**, the installer for the ADI SDP Drivers will execute.\\ <WRAP left tip round box 60%> | ||
| + | - Press **Next** to set the installation location for the **SDP Drivers**\\ <WRAP left round tip 50%>It is recommended that you install the drivers to the default directory path \\ **C: | ||
| + | - Press **Next** to install the **SDP Drivers**. When prompted by Windows Security, just press **Install**\\ {{: | ||
| + | - Press **Finish** to complete the installation\\ {{: | ||
| + | |||
| + | ---- | ||
| + | |||
| + | ===== Using the Evaluation Software ===== | ||
| + | ==== Main Window ==== | ||
| + | {{ : | ||
| + | * **Title Bar** <fc # | ||
| + | * **Connect Button** | ||
| + | * Starts the connection with the [[ADI> | ||
| + | * **Disconnect Button** | ||
| + | * Ends the connection with the [[ADI> | ||
| + | * **System Configuration** <fc # | ||
| + | * **Connector** | ||
| + | * Selects which 120-pin connection of the **SDP-B Board** to use | ||
| + | * **SCLK (Hz)** | ||
| + | * Sets the SPI clock frequency used by the evaluation board | ||
| + | * **AD5751 Configuration** <fc # | ||
| + | * **JP1 Configuration** | ||
| + | * Sets the SPI address of the AD5750-1 based on the position of JP1 | ||
| + | * **Range Select** | ||
| + | * Sets the voltage/ | ||
| + | * **Toggle CLEAR** | ||
| + | * Sets the outputs to the zero/ | ||
| + | * **AD5751 Error Indicator** <fc # | ||
| + | * **Vout Fault** | ||
| + | * There is a short circuit on the VOUT pin | ||
| + | * **Iout Fault** | ||
| + | * There is an open circuit on the IOUT pin | ||
| + | * **Over Temp** | ||
| + | * The AD5751 core temperature exceeds 150 °C | ||
| + | * **PEC Error** | ||
| + | * CRC-8 error checking detected an interface error | ||
| + | * **Output Setting** <fc # | ||
| + | * **Write AD5662** | ||
| + | * Writes the hexadecimal value in the left field to the AD5662 output voltage | ||
| + | * **Reset AD5751** | ||
| + | * Resets the AD5751 to its power-on state | ||
| + | * **Quit** | ||
| + | * Exits the software application | ||
| + | ==== Running the System ==== | ||
| + | - Open the **CN0204.exe** application from the default installation location. | ||
| + | - Set the correct connector and SCLK settings for the board in the System Configuration section. | ||
| + | - Click the **Connect Button** | ||
| + | - Upon successful connection, select the desired range of output on the Range Select drop-down menu. | ||
| + | - Input a hex value equivalent of the desired output level in the Output Setting section. | ||
| + | - Click **Write AD5662** | ||
| + | - Click **Disconnect Button** if finished. | ||
| + | |||
| + | ---- | ||
| + | |||
| + | ===== More Information and Useful Links ===== | ||
| + | * [[ftp:// | ||
| + | * [[ADI> | ||
| + | * [[ADI> | ||
| + | * [[ADI> | ||
| + | * [[ADI> | ||
| + | |||
| + | |||
| + | ===== Schematic, PCB Layout, Bill of Materials ===== | ||
| + | |||
| + | <WRAP round 80% download> | ||
| + | [[adi> | ||
| + | * Schematics | ||
| + | * PCB Layout | ||
| + | * Bill of Materials | ||
| + | * PADS project | ||
| + | </ | ||
| + | |||
| + | =====Registration===== | ||
| + | <WRAP round tip 80% > | ||
| + | Receive software update notifications, | ||
| + | |||
| + | //End of Document// | ||
resources/eval/user-guides/circuits-from-the-lab/cn0204.1501815550.txt.gz · Last modified: 04 Aug 2017 04:59 by Angelo Nikko Catapang