Differences
This shows you the differences between two versions of the page.
| Both sides previous revisionPrevious revisionNext revision | Previous revisionLast revisionBoth sides next revision | ||
| resources:eval:user-guides:circuits-from-the-lab:cn0188 [03 Nov 2017 03:52] – update Trisha Cabildo | resources:eval:user-guides:circuits-from-the-lab:cn0188 [03 Jan 2021 21:55] – fix links Robin Getz | ||
|---|---|---|---|
| Line 15: | Line 15: | ||
| ===== Required Equipment ===== | ===== Required Equipment ===== | ||
| * [[adi> | * [[adi> | ||
| - | * [[http:// | + | * [[adi>EVAL-SDP-CB1Z|EVAL-SDP-CB1Z]] Controller Board (**SDP-B Board**) |
| * [[ftp:// | * [[ftp:// | ||
| * Power Supply | * Power Supply | ||
| Line 29: | Line 29: | ||
| ==== Block assignments ==== | ==== Block assignments ==== | ||
| {{ : | {{ : | ||
| - | * The [[http:// | + | * The [[adi>EVAL-CN0188-SDPZ|EVAL-CN0188-SDPZ]] **(CN-0188 Board)** connects to the [[adi>EVAL-SDP-CB1Z|EVAL-SDP-CB1Z]] **(SDP-B Board)** via the 120-Pin connector |
| - | * The [[http:// | + | * The [[adi>EVAL-SDP-CB1Z|EVAL-SDP-CB1Z]] **(SDP-B Board)** connects to the PC via the USB cable. |
| * Terminal block **J2** is the +6 V barrel connector for wall wart supply input | * Terminal block **J2** is the +6 V barrel connector for wall wart supply input | ||
| * Terminal block **J3** is the test point for 6 V DC output | * Terminal block **J3** is the test point for 6 V DC output | ||
| Line 39: | Line 39: | ||
| {{ : | {{ : | ||
| - | - Connect the 120-pin connector on the [[adi> | + | - Connect the 120-pin connector on the [[adi> |
| - Connect a shunt resistor across the input terminals with a load to ground as indicated in figure above | - Connect a shunt resistor across the input terminals with a load to ground as indicated in figure above | ||
| - With power to the supply off, connect a +6 V power supply to the pins marked “+6V” and “GND” on the board | - With power to the supply off, connect a +6 V power supply to the pins marked “+6V” and “GND” on the board | ||
| Line 66: | Line 66: | ||
| ===== Using the Evaluation Software ===== | ===== Using the Evaluation Software ===== | ||
| ====Test Setup Tab==== | ====Test Setup Tab==== | ||
| - | {{ : | + | ==== Main Window ==== |
| - | | + | {{ : |
| + | - **Connect** Button - Starts the connection between the [[ADI> | ||
| + | - **Disconnect** Button - Ends the connection between the [[ADI> | ||
| + | - **Select SDP Connector** - Selects which 120-pin connection of the SDP-B Board to use | ||
| + | - **Shunt Voltage Input** - Determines input shunt voltage level in millivolts | ||
| + | - **Temperature** - Temperature level test conditions of input signal | ||
| + | - **Data Acquisition** Controls | ||
| + | * **Sample Data** - Start acquisition of measurement data | ||
| + | * **Remove Data Point** - Remove a data point from samples | ||
| + | * **Save Data** - Save measurement data to file | ||
| + | * **Clear Data** - Clear the current measurement data | ||
| + | | ||
| + | * **ADC Code Plot** Enable - Show or hide the ADC Code plot | ||
| + | * **Error Plot** Enable - Show or hide the Error plot | ||
| + | * **Converted Shunt Voltage** - Shunt voltage value from the ADC | ||
| + | * **Over/ | ||
| + | * **Plot Options** - Edit plot display and options like interpolation and color of output waveform | ||
| + | - **Administration** Tab \\ {{ : | ||
| + | * **Flash LED** - Flashes the LED on the SDP controller board | ||
| + | * **Read Firmware** - Reads the firmware of CN0240 Evaluation Board | ||
| + | - **Quit** Button - Closes the evaluation software\\ | ||
| \\ | \\ | ||
| + | ==== Running the System ==== | ||
| + | -Open the CN0188.exe application from the default installation location | ||
| + | -Set the correct connector and click the Connect Button | ||
| + | -Upon successful connection, set the desired input signal parameters such as shunt voltage and temperature | ||
| + | -Start and control data acquisition through the data acquisition control buttons | ||
| + | -Output data will be shown in the graph. Edit graph through plot options and check boxes provided | ||
| + | -Click Disconnect if finished | ||
| + | -Click Quit to exit the program | ||
| + | |||
| + | \\ | ||
| ---- | ---- | ||
| Line 75: | Line 105: | ||
| * [[ftp:// | * [[ftp:// | ||
| * [[ADI> | * [[ADI> | ||
| - | * [[http:// | + | * [[adi>media/ |
| * [[ADI> | * [[ADI> | ||
| Line 85: | Line 115: | ||
| <WRAP round 80% download> | <WRAP round 80% download> | ||
| - | [[http:// | + | [[adi>media/ |
| * Schematics | * Schematics | ||
| * PCB Layout | * PCB Layout | ||
resources/eval/user-guides/circuits-from-the-lab/cn0188.txt · Last modified: 30 Jul 2021 07:14 by Victor Calinao, Jr