This version is outdated by a newer approved version.
This version (28 Jan 2021 19:59) was approved by Robin Getz.The Previously approved version (14 Oct 2016 15:03) is available.
This version (28 Jan 2021 19:59) was approved by Robin Getz.The Previously approved version (14 Oct 2016 15:03) is available.This is an old revision of the document!
Table of Contents
AD-FMCOMMS3-EBZ Hardware
Downloads
This is the latest, greatest and production worthy Rev “A” of this board (Although it indicates “A”, this is not the first version, and there is no Rev B planned). Note that the RF transformers used as baluns on the Rev A board are Mini Circuits TCM1-63AX+. They are rated for a operating frequency between 10 MHz and 6 GHz.
- Rev A Allegro Board File (This file is compressed). Get the Allegro FREE Physical Viewer (You need 16.5 or higher).
I/O Voltage
The AD-FMComms3 (AD9361) assumes a VDD_INTERFACE voltage between 1.71V and 2.625V (1.8 to 2.5 +/- 5%), so on your FPGA carrier board, you should ensure that VADJ is between these levels. Setting things to 3.3V will damage the part.
Picture and Main components
Outline
For those that don't want to load up the Allegro viewer, here is a basic outline/component placements of the board. While this board does meet parts of the VITA-57.1 (FMC) specifications, there are many things it violates, and is not designed to be a form/fit/function board.
- The FMC cutout for the bezel is missing (so we could space the SMA connectors out as far as possible, and achieve maximum isolation between the channels.
- The mounting holes near the end of the board with the connectors is also in the wrong place (so it didn't effect the RF path between the connectors and the AD9361.
- The FMC height specification on the top side of the board is violated to put some 90 degree SMA connectors.
Size
The size of the board (not including the SMA connectors, which project beyond the edge of the board) is 73.3mm x 69mm. This is under the FMC specifications of 84mm x 69mm). The mounting holes are not compliant with the FMC standard, and are shown below.
Layers
The AD-FMCOMMS3-EBZ is a 10 layer board.
Design Cross Section
| Subclass Name | Type | Material | Thickness (MIL) | Conductivity (mho/cm) | Dielectric Constant | Loss Tangent | Shield | Width (MIL) |
|---|---|---|---|---|---|---|---|---|
| SURFACE | AIR | 0 | 1 | 0 | ||||
| TOP | CONDUCTOR | COPPER | 2.025 | 595900 | 1 | 0 | 8.00 | |
| DIELECTRIC | FR-4 | 8 | 0 | 3.38 | 0.035 | |||
| L2_GND | PLANE | COPPER | 1.35 | 595900 | 1 | 0.035 | Y | |
| DIELECTRIC | BT_EPOXY | 3 | 0 | 4.10 | 0.02 | |||
| L3_PWR | PLANE | COPPER | 1.35 | 595900 | 1 | 0.035 | Y | |
| DIELECTRIC | FR-4 | 3 | 0 | 4.10 | 0.035 | |||
| L4_GND | PLANE | COPPER | 1.35 | 595900 | 1 | 0.035 | Y | |
| DIELECTRIC | BT_EPOXY | 4.60 | 0 | 4.10 | 0.02 | |||
| L5_SIG | CONDUCTOR | COPPER | 1.35 | 595900 | 1 | 0.035 | 3.80 | |
| DIELECTRIC | FR-4 | 8 | 0 | 4.10 | 0.035 | |||
| L6_SIG | CONDUCTOR | COPPER | 1.35 | 595900 | 1 | 0.035 | 3.80 | |
| DIELECTRIC | BT_EPOXY | 4.60 | 0 | 4.10 | 0.02 | |||
| L7_GND | PLANE | COPPER | 1.35 | 595900 | 1 | 0.035 | Y | |
| DIELECTRIC | FR-4 | 3 | 0 | 4.10 | 0.035 | |||
| L8_PWR | PLANE | COPPER | 1.35 | 595900 | 1 | 0.035 | Y | |
| DIELECTRIC | BT_EPOXY | 3 | 0 | 4.10 | 0.02 | |||
| L9_GND | PLANE | COPPER | 1.35 | 595900 | 1 | 0.035 | Y | |
| DIELECTRIC | FR-4 | 8 | 0 | 3.38 | 0.035 | |||
| BOTTOM | CONDUCTOR | COPPER | 2.025 | 595900 | 1 | 0 | 8.00 | |
| SURFACE | AIR | 0 | 1 | 0 |
resources/eval/user-guides/ad-fmcomms3-ebz/hardware.1611860226.txt.gz · Last modified: 28 Jan 2021 19:57 by Robin Getz