Wiki

Analog Devices Wiki

English
English
简体中文
简体中文
日本語
日本語
Руccкий
Руccкий

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
resources:eval:dpg:ad9739-ebz [20 Sep 2021 03:28] – Update to SDPH1 and ADSV7 Melissa Lorenz Lacanlaleresources:eval:dpg:ad9739-ebz [15 Feb 2022 02:28] (current) – [Software Needed:] Melissa Lorenz Lacanlale
Line 33: Line 33:
 =====Software Needed:===== =====Software Needed:=====
   * [[:resources:tools-software:ace|Analysis | Control | Evaluation (ACE) Software]]   * [[:resources:tools-software:ace|Analysis | Control | Evaluation (ACE) Software]]
-  * [[:resources:tools-software:ace:dpg-lite|DPG Lite]] or [[:resources:eval:dpg:dpgdownloader|DPG Downloader]]+  * [[:resources:tools-software:ace:dpg-lite|DPG Lite]] (Recommended; Installed with ACE)  or [[:resources:eval:dpg:dpgdownloader|DPG Downloader]] 
 + <note important>**Known Issue:** ACE may fail to detect HS-DAC boards, details [[resources:tools-software:ace:knownissues#high-speed_dac_eval_boards_are_not_discovered|here]].</note> 
  
 =====Hardware Needed:===== =====Hardware Needed:=====
   * [[adi>eval-ad9739|AD9739-R2-EBZ]] Evaluation Board   * [[adi>eval-ad9739|AD9739-R2-EBZ]] Evaluation Board
   * [[:resources:eval:dpg:hsdac-sdp-h1|SDP-H1]] (EVAL-SDP-CH1Z) or [[:resources:eval:ads7-v2|ADS7-V2EBZ]]    * [[:resources:eval:dpg:hsdac-sdp-h1|SDP-H1]] (EVAL-SDP-CH1Z) or [[:resources:eval:ads7-v2|ADS7-V2EBZ]] 
-  * Evaluation Kit 
   * [[adi>AD-DAC-FMC]]-ADP High-Speed DAC Evaluation Board to FMC Adaptor Board   * [[adi>AD-DAC-FMC]]-ADP High-Speed DAC Evaluation Board to FMC Adaptor Board
   * 5Vdc 2A Power Supply   * 5Vdc 2A Power Supply
Line 56: Line 57:
  
 =====Quick Start Guide===== =====Quick Start Guide=====
-  - Attach the evaluation board to the FMC connector of SDP-H1 or ADS7-V2 using the AD-DAC-FMC-ADP adapter board. Connect continuous wave generator for clock input to J3, and the DAC output from J1 to a signal/spectrum analyzer. Connect the evaluation board to PC via USB and a 5Vdc 2A power supply to J17. Refer to Figures 1a and 1b.+  - Attach the evaluation board to the FMC connector of SDP-H1 or ADS7-V2 using the AD-DAC-FMC-ADP adapter board. Connect continuous wave generator for clock input to J3, and the DAC output from J1 to a signal/spectrum analyzer. Connect the evaluation board to PC via USB, a 5Vdc 2A power supply to J17. Refer to Figures 1a and 1b.
      * If using **SDP-H1**, set clock input to **300 MHz and 0 dBm**. Connect SDP-H1 to PC via USB and to a 12Vdc wall wart.      * If using **SDP-H1**, set clock input to **300 MHz and 0 dBm**. Connect SDP-H1 to PC via USB and to a 12Vdc wall wart.
      * If using **ADS7-V2**, set the clock input to **2 GHz and 0 dBm**. Connect ADS-V2 to PC via USB and to a 12V 60W AC/DC power supply. Switch the board ON using S1 beside the connector for 12V supply.      * If using **ADS7-V2**, set the clock input to **2 GHz and 0 dBm**. Connect ADS-V2 to PC via USB and to a 12V 60W AC/DC power supply. Switch the board ON using S1 beside the connector for 12V supply.
-  - Open ACE. The board will automatically be recognized by the software. Otherwise, install the plugin for AD9739 evaluation board. From the AD9739-EBZ tab, Click **“Run Example Startup Routine (Sync Disabled)”**. The **MU Controller Locked** indicator should light up as shown in figure 2.  <WRAP centeralign>{{ :resources:eval:dpg:ad9739_ace_boardview.png?nolink&600 |}}//Figure 2. ACE Initial Board Configuration Wizard //</WRAP> +  - Open ACE. The board will automatically be recognized by the software. Otherwise, install the plugin for AD9739 evaluation board. From the AD9739-EBZ tab, Click **“Run Example Startup Routine (Sync Disabled)”**.  
-  - Double click the AD9739 Box to open chip view. The **DLL_LOCKED** indicator should be enabled as shown in figure 3.<WRAP centeralign>{{ :resources:eval:dpg:ad9739_ace_chipview.png?nolink&600 |}}//Figure 3. ACE Initial Chip  Configuration Wizard//</WRAP>+     * If using **SDP-H1**, The MU Controller Locked indicator should light up as shown in figure 2a. 
 +     * If using **ADS7-V2**, The first three indicators should light up as shown in figure 2b. <WRAP centeralign>{{ :resources:eval:dpg:ad9739_ace_boardview.png?nolink&600 |}}//Figure 2a. ACE Initial Board Configuration Wizard for SDP-H1//</WRAP> <WRAP centeralign>{{ :resources:eval:dpg:ad9739_ads7_ace_boardview.png?nolink&600 |}}//Figure 2a. ACE Initial Board Configuration Wizard for ADS7-V2//</WRAP> 
 +  - Double click the AD9739 Box to open chip view.  
 +     * If using **SDP-H1**, The DLL_LOCKED indicator should light up as shown in figure 3a. 
 +     * If using **ADS7-V2**, All three indicators should light up as shown in figure 3b. <WRAP centeralign>{{ :resources:eval:dpg:ad9739_ace_chipview.png?nolink&600 |}}//Figure 3a. ACE Initial Board Configuration Wizard for SDP-H1//</WRAP> <WRAP centeralign>{{ :resources:eval:dpg:ad9739_adsv7_ace_chipview.png?nolink&600 |{{ :resources:eval:dpg:ad9739_ads7_ace_boardview.png?nolink&600 |}}//Figure 3b. ACE Initial Board Configuration Wizard for ADS7-V2//</WRAP>
   - Start DPG Lite or DPG Downloader.   - Start DPG Lite or DPG Downloader.
-    * At the SDP-H1 part of the software, the device part number and **DCO frequency** of around **75 MHz** should be displayed. +    * At the SDP-H1 settings, ensure that Evaluation board is equal to AD9739 and **DCO frequency** of around **75 MHz** should be displayed. 
-    * At the ADS7-V2 part of the software, the device part number and **DCO frequency** of around **500 MHz** should be displayed.+    * At the ADS7-V2 settings, ensure that Evaluation board is equal to AD9739 and **DCO frequency** of around **500 MHz** should be displayed.
   - In DPG Lite or DPG Downloader, from the **Add Generator Waveforms** pulldown menu, select **Single Tone** and apply the settings as shown in Figures 4a and 4b.    - In DPG Lite or DPG Downloader, from the **Add Generator Waveforms** pulldown menu, select **Single Tone** and apply the settings as shown in Figures 4a and 4b. 
     * When using SDP-H1, set **Data Rate** to 300 MHz and **Desired Frequency** to 20 MHz.     * When using SDP-H1, set **Data Rate** to 300 MHz and **Desired Frequency** to 20 MHz.
Line 74: Line 79:
 =====Troubleshooting===== =====Troubleshooting=====
 This section lists items to check and practices to use when debugging any unexpected performance of a board. If unexpected results occur: This section lists items to check and practices to use when debugging any unexpected performance of a board. If unexpected results occur:
-  * Check the supply voltage of the evaluation board. Voltage rail should be 3.3V.+  * Check if the Voltage supply test points of the evaluation board has the correct value. 
   * Check if all (3) blue LEDs on the AD-DAC-FMC-ADP board is lit up. Reconnect the board to the FMC connector of SDP-H1 if not lit up.   * Check if all (3) blue LEDs on the AD-DAC-FMC-ADP board is lit up. Reconnect the board to the FMC connector of SDP-H1 if not lit up.
   * Check if the SDP-H1 is being supplied properly by 12Vdc adaptor. Some LEDs on the SDP-H1 should lit up.   * Check if the SDP-H1 is being supplied properly by 12Vdc adaptor. Some LEDs on the SDP-H1 should lit up.
resources/eval/dpg/ad9739-ebz.1632101337.txt.gz · Last modified: 20 Sep 2021 03:28 by Melissa Lorenz Lacanlale

Page Tools