Wiki

Analog Devices Wiki

English
English
简体中文
简体中文
日本語
日本語
Руccкий
Руccкий

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Last revisionBoth sides next revision
resources:eval:ad9467-fmc-250ebz [09 Jan 2021 00:22] – user interwiki links Robin Getzresources:eval:ad9467-fmc-250ebz [05 Oct 2021 23:05] – Added AD9517 setup instructions, updated ftp links Alex Arrants
Line 30: Line 30:
   * [[adi>an-835|AN-835 Application Note]], //Understanding ADC Testing and Evaluation//   * [[adi>an-835|AN-835 Application Note]], //Understanding ADC Testing and Evaluation//
 ===== Software Needed ===== ===== Software Needed =====
-  * VisualAnalog [[ftp://ftp.analog.com/pub/HSSP_SW/VisualAnalog/VisualAnalog_Setup.exe]]    +  * [[adi>VisualAnalog|VisualAnalog]]   
-  * SPIController [[ftp://ftp.analog.com/pub/adispi/A2DComponents/Install/SPIController_Setup.exe]]+  * [[adi>/en/design-center/interactive-design-tools/spicontroller.html|SPIController]]   
 +  
 ===== Design and Integration Files ===== ===== Design and Integration Files =====
-  * FPGA BIN file ftp://ftp.analog.com/pub/HSC_ADC_Apps/SDP-H1/ad9467_sdp_h1.bin+  * {{:resources:eval:ad9467fmc:ad9467_sdp_h1.zip|FPGA bin file (Unzip before use)}}
   * [[/resources/fpga/xilinx/fmc/ad9467#downloads |Schematics, Bill Of Materials, and Gerber Layout/Fabrication Files]]    * [[/resources/fpga/xilinx/fmc/ad9467#downloads |Schematics, Bill Of Materials, and Gerber Layout/Fabrication Files]] 
 ===== Equipment Needed ===== ===== Equipment Needed =====
Line 106: Line 107:
   * Ensure that the ADC has a valid clock input   * Ensure that the ADC has a valid clock input
  
 +===== AD9517-4 Configuration (Optional) =====
 +The AD9467-FMC-250EBZ is configured from the factory to use an external clock connected to J201. Alternatively, the AD9467-FMC-250EBZ can be configured to use the on-board 25MHz oscillator and AD9517-4 Clock Generator to generate the 250 Msps clock input. (Note: some boards have shipped with a 250 MHz oscillator and will require a different configuration)
 +
 +** Hardware Modifications **
 +   *Remove the following components: R209, R210, C209, C210
 +   *Add the following components: C205, C206, C300, C301, C304, C305
 +   *Make sure that Jumper P200 is on the "On" Position
 +
 +**Additional Software Needed**
 +   *{{:resources:eval:ad9467fmc:configure_ad9517_ad9467-fmc-250ebz_.zip|configure_ad9517_AD9467-FMC-250EBZ MGP file}}
 +** Setup Instructions **
 +  - Make sure that a clock source is not connected to J201
 +  - Configure SPIcontroller and VisualAnalog as described above
 +  - Launch a 2nd instance of SPIController.
 +  - Load the AD9517spiR03.cfg configuration file.
 +  - Click Config>Controller Dialog
 +  - Select "2" Under FIFO Chip Sel # {{ :resources:eval:ad9467fmc:SPI_Controller_Cfg_Dialog2.PNG?262 |}}<WRAP centeralign>
 +//Figure 12. Select Fifo Chip Sel # 2 in SPIController//</WRAP>
 +  - Click Apply and OK
 +  - Click File>Macro Group Open
 +  - Select the configure_ad9517_AD9467-FMC-250EBZ .mgp file
 +  - Check the Enable Check Box {{ :resources:eval:ad9467fmc:MacroEditor-Enable.PNG?375 |}}<WRAP centeralign>
 +//Figure 13. Select Enable Macro in SPIController//</WRAP>
 +  - Click Run Macros {{ :resources:eval:ad9467fmc:run.PNG?23 |}}<WRAP centeralign>
 +//Figure 14. Click Run Macros in SPIController//</WRAP>
 +  - Make sure that LED CR300 is illuminated on the AD9467-FMC-250EBZ.
 +
 +** Obtaining an FFT **
 +  - Click the Run button in VisualAnalog , you should see the captured data similar to the plot shown in Figure 9 {{ :resources:eval:ad9467fmc:fft-ad9517.png?736 |}} <WRAP centeralign>
 +//Figure 15. AD9467-FMC-250 FFT at 140.3MHz Analog Input (performance may be degraded compared to high-quality direct clock)//</WRAP>
  
  
  
resources/eval/ad9467-fmc-250ebz.txt · Last modified: 25 Apr 2023 13:29 by Iulia Moldovan

Page Tools