Wiki

Below is the source of this page. To edit this source as well as other pages on the wiki, you must login.
===== AD-FMCDAQ2-EBZ Quick Start Guides =====

The Quick Start Guides provide a simple step by step instruction on how to do an initial system setup for the AD-FMCDAQ2-EBZ boards on various FPGA development boards. They will discuss how to program the bitstream, run a no-OS program or boot a Linux distribution.

==== Supported Carriers ====

The AD-FMCDAQ2-EBZ is, by definition a "FPGA mezzanine card" (FMC), that means it needs a carrier to plug into. The carriers we support are:

^ Board ^ Quickstart Guide ^
| [[https://www.altera.com/products/boards_and_kits/dev-kits/altera/arria-10-soc-development-kit.html|Arria10 SoC Dev Kit]] | [[./quickstart/a10soc|AD-FMCDAQ2-EBZ Arria10 SoC Development Kit Quick Start Guide]] |
| [[https://www.altera.com/products/boards_and_kits/dev-kits/altera/kit-a10-gx-fpga.html|Arria10 GX FPGA Dev Kit]] | [[./quickstart/a10soc|AD-FMCDAQ2-EBZ Arria10 GX FPGA Development Kit Quick Start Guide]] |
| [[xilinx>KC705]] | [[./quickstart/microblaze|AD-FMCDAQ2-EBZ Microblaze Quick Start Guide]] |
| [[xilinx>KCU105]] | [[./quickstart/microblaze|AD-FMCDAQ2-EBZ Microblaze Quick Start Guide]] |
| [[xilinx>VC707]] | [[./quickstart/microblaze|AD-FMCDAQ2-EBZ Microblaze Quick Start Guide]] |
| [[xilinx>ZC706]] | [[./quickstart/zynq|AD-FMCDAQ2-EBZ Zynq ZC706 Quick Start Guide]] |
| [[xilinx>ZCU102]] | [[:resources:eval:user-guides:ad-fmcdaq2-ebz:quickstart:zcu102|AD-FMCDAQ2-EBZ ZynqMP ZCU102 Quick Start Guide]] |

The supported OS are:

^ Board ^ HDL ^ Linux Software ^ No-OS Software ^ 
| [[https://www.altera.com/products/boards_and_kits/dev-kits/altera/arria-10-soc-development-kit.html|Arria10 SoC Dev Kit]] |  YES  |  NO  |  YES  |
| [[https://www.altera.com/products/boards_and_kits/dev-kits/altera/kit-a10-gx-fpga.html|Arria10 GX FPGA Dev Kit]] |  NO (only until [[repo>hdl/tree/hdl_2021_r1/projects/daq2/a10gx|hdl_2021_r1]] branch)  |  NO  |  YES  |
| [[xilinx>KC705]] |  YES  |  YES  |  YES  |
| [[xilinx>KCU105]] |  YES  |  YES  |  YES  |
| [[xilinx>VC707]] |  NO (only until [[repo>hdl/tree/hdl_2018_r2/projects/daq2/vc707|hdl_2018_r2]] branch)  |  YES  |  YES  |
| [[xilinx>ZC706]] |  YES  |  YES  |  YES  |
| [[xilinx>ZCU102]] |  YES  |  YES  |  YES  |
 

==== Hardware Setup ====

In most carriers, the AD-FMCDAQ2-EBZ board connects to the HPC connector (unless otherwise noted). 
The carrier setup requires power, UART (115200), ethernet (Linux), HDMI (if available) and/or JTAG (no-OS) connections. 
A typical setup is shown below.

{{ :resources:eval:user-guides:ad-fmcdaq2-ebz:software:linux:ad-fmcdaq2-ebz_zc706.png?800 |}}
Analog Devices Wiki

Page Tools
