This version is outdated by a newer approved version.
This version (14 Apr 2021 16:33) was approved by Shine Cabatan.The Previously approved version (07 Apr 2021 10:43) is available.
This version (14 Apr 2021 16:33) was approved by Shine Cabatan.The Previously approved version (07 Apr 2021 10:43) is available.This is an old revision of the document!
Table of Contents
EVALUATING THE AD9704/AD9705/AD9706/AD9707 DIGITAL-TO-ANALOG CONVERTER
Preface
This user guide describes both the hardware and software setup needed to acquire data capture from AD9704-DPG2-EBZ/AD9705-DPG2-EBZ/AD9706-DPG2-EBZ/AD9707-DPG2-EBZ evaluation board to characterize AD9704/AD9705/AD9706/AD9707 8-/10-/12-/14-bit 175Msps high-speed digital-to-analog converter.
This guide will focus on how AD970x-DPG2-EBZ works with SDP-H1 controller board developed by Analog Devices. Link to the old user guide document is provided for customers who still have DPG2 and DPG3 controller boards.
Typical Setup
Figure 1. EVAL-AD970x Evaluation Setup
Tip: Click on any picture in this guide to open an enlarged version.
Helpful Files:
- User Guide for DPG2/3 users and as reference on evaluation board jumper selection
Tip: Open this page in Internet Explorer to avoid problems when downloading files.
Software Needed:
Hardware Needed:
- SDP-H1 (EVAL-SDP-CH1Z) Board
- 12V 1A Wall Adapter for SDP-H1
- AD-DAC-FMC-ADP High-Speed DAC Evaluation Board to FMC Adaptor Board
- PC with ACE and DPG Lite Software Applications
- High-Frequency Continuous Wave Generator
- Signal/Spectrum Analyzer
- (2) USB A to USB Mini Cables
- (2) SMA Cables
Quick Start Guide
- Attach AD9704-DPG2-EBZ/AD9705-DPG2-EBZ/AD9706-DPG2-EBZ/AD9707-DPG2-EBZ to SDP-H1 FMC connector using the AD-DAC-FMC-ADP adapter board. Connect continuous wave generator for clock input to J10 and DAC output from S4 to a signal/spectrum analyzer. Connect the evaluation board to PC via USB. Refer to Figure 1.
- Connect SDP-H1 to PC via USB and to a 12V 1A power supply.
- Set clock input to 175MHz and 13dBm.
- Open ACE. The board will be automatically recognized by the software. Otherwise, install the plugin for AD9707.
- Start DPG Lite or DPG Downloader. At the SDP-H1 part of the software, the device part number and clock frequency should be displayed.
- In ACE, apply the default values in the Initial Configuration wizard as shown in Figure 2.
Figure 2. ACE Initial Configuration Wizard for EVAL-AD9707
- In DPG Lite or DPG Downloader, from the Add Generator Waveforms pulldown menu select Single Tone and apply the settings as shown in Figure 3. Set the desired frequency to 20 MHz. Set DAC resolution to the DAC’s number of bits (14 for AD9707, 12 for AD9706, and so on). Check the Unsigned Data box.
Figure 3. DPG Lite session for EVAL-AD9707
- Select the tone from the Data Vector pulldown menu.
- Press the download arrow and then the play button. The spectrum similar to Figure 4 should appear in the signal/spectrum analyzer.
Figure 4. EVAL-AD9707 FFT for Fdac=175MHz, Fout=20MHz
resources/eval/dpg/eval-ad970x.1618410816.txt.gz · Last modified: 14 Apr 2021 16:33 by Shine Cabatan